Welcome, Guest
Email: Password: Remember me
Street Vehicles For Sale
  • Page:
  • 1

TOPIC: 1976 Camaro Street Machine Project

1976 Camaro Street Machine Project 1 year, 10 months ago #1284

1976 Camaro Street Machine Project

I’ve decided to sell my 5 year slow project "again" due to personal health reasons.

This car is almost 100% complete to be road worthy and drivable, the body work was to be done after all of the mechanical. The 383 short block has recently been changed due to a hard freeze in Dec 09 that cracked the block. My original machinist swapped the parts from the cracked block to a new seasoned block with the same specs. I haven’t built the engine back up yet but I have all the parts to do it. When the original engine was running it sounded and drove very very strong, only had 3 hours run time and a mile or 2 on the road. Have many digital photos during build. Also have a bunch of receipts for parts.

Asking $6000 OBO (will not part out) serious inquiries only, if you’re looking for a great ground start for a 2nd generation Camaro this is well worth it, come see to appreciate. A couple thousand dollars after time and some TLC this will be a looker. Located in Owasso OK. Car will have to be trailored.

Thanx for looking,
Eddie

Below is one of those “too much to list” lists…but I listed it anyway.

Things it needs to be road worthy first:
- finish bolting stuff on engine
- full front suspension/steering alignment
- power steering pump (have newer lines)
- exhaust from headers back
- re-install complete front clip
- install hood (fiberglass 4 in cowl, older Harwood model unfinished belly)
- complete brake bleed (all new brakes)
- more engine, rear end, and tranny break-in
- has a clear title and a black tag

….more work to be done later
- full weather strip kit
- body/paint work
- heater core installed (have new one, also a ACdelete cover)
- door hinges while fenders are off (have extra set w/new bushing kit)
- windshield has cracks at wiper
- needs door/trunk key set (pass door missing)

What it has:

ENGINE
- 383 stroker short block (short block built by Richards Performance Machine in Wagner OK)
- created from a 1986 350 4 bolt main block w/one piece rear main seal
- rated between 400 – 450 horse
- Scat cast 383 crank
- stock GM rods
- Speed Pro hypereutectic pistons
- high volume oil pump (60psi at gauge)
- Milodon oil pan
- Weiand Aluminum water pump
- Aluminum pulleys
- 4 core radiator w/custom over flow tank
- new GM shroud
- Professional Products RPM Air Gap manifold
- Road Demon Jr. 4 Barrel Carb 625cm w/vac sec
- 1in aluminum carb spacer
- K&N 4 x14 air cleaner
- Edlebrock mechanical fuel pump 80 gpm at 8psi (no regular needed)
- Word Products 2.02 heads w/crane 1.5 roller rockers (built by Len Williams OK)
- New Pioneer Race products 1.5 dual valve springs w/10 degree locks (correct for Cam)
- Comp Cams Extreme Energy XE284H-10 w/matching hyd lifters
- gross valve lift I .507 E .510
- tappet lift I 284 E 296
- duration @ .050 I 240 E 246
- lobe lift I .3380 X .3410
- lobe separation 110.0
- Cloyes double roller timing chain set
- Professional Products balancer
- Taylor 8mm spark plug wires (red)
- billet aluminum GM distributor w/65K volt internal coil
- Scat SFI grade flywheel
- Hedmen Elite ceramic hedders (with temporary glass packs)
- Flex-a-lite fan clutch w/stock 17in fan
- new battery
- new mini hi-torque starter
- Summit 1 wire H/O alternator w/rod end style bracket
- Poly Urethane motor mounts

TRANS
- Turbo 350 (newly rebuilt, same miles as motor)
- B&M Shift kit
- B&M Holeshot 3000 stall converter 2800-3200 stall
- Trick Flow deep 7 qt aluminum trans pan
- B&M Trans cooler
- B&M fluid
- Poly Urethane trans mount
- new speedo and B&M shifter cables

REAREND
- 10 bolt 8.5 corporate (built by Danny’s Diff’s OK)
- Auburn Posi-Unit
- new 28 spline Alloy USA axles
- Yukon 3:73 ring and pinion
- Summit heavy duty aluminum cover w/bearing-cap support
- all new bearings
- extra long Moroso wheel studs
- Lucas fluid

CHASSIS
- Comp Engineering traction bars
- Comp Engineering sub-frame connectors
- new multi leaf (4) leaf spings
- Poly Urethane leaf spring eye and pad bushing
- rebuilt and balanced drive shaft w/solid U-Joints
- new shackles
- Rear Air shocks
- new Russell braided brake lines, front and rear
- new rear brake hardware, pads
- new stock front brake calipers
- stock front spindles
- new drilled/slotted front rotors w/new wheel studs
- PST 1 ½ in sway bar
- sub-frame striped, primed, painted black)
- all PST Poly Urethane bushing throughout front
- new Z28 front coil springs
- all new PST tie-rods and center link
- new ball joints
- new A-frame bushings
- Poly Urethane sub-frame bushings
- new GM gas tank w/new sending unit
- new chrome brake power booster
- new stock brake master cylinder
- new proportioning valve

INTERIOR
- still has complete black interior minus carpet, headliner, and rear package tray
- center console
- B&M Quick Silver console shifter
- new Scat rap around style bucket seats (black)
- new red 4 point harness style DOT approved seat belts (not SFI approved)
- 2 5/8 Sunpro triple gauge cluster (temp, oil, volt)
- 3.5 inch Sunpro tach
- tilt steering
- power windows
- no stereo
- original A/C car (A/C removed in front but ducking and controls still there
- would need to replace original dash to be nice (warped)

BODY
- has a few rust concerns where vinyl top was around lower rear window and roof
- rust on lower quarter panel about half dollar size
- rust on lower pass door (was going to re-skin, but repairable)
- minor dings and a few bigger dings
- 4 in cowl hood, older Harwood model unfinished belly (still have original hood)
- aluminum bumpers have nicks and scratches
- complete window trim
- different front header panel (original cracked at hood latch)
- no spoiler

WHEELS
- Corvette style Ralley’s w/rings and dog dish caps
- 15x10 rear w/295-50 (worn but work)
- 15x7 front w/205-65 (worn but work)
- still have original 14x7 Camaro ralleys w/tires
Attachments:
  • Attachment This image is hidden for guests. Please log in or register to see it.
  • Attachment This image is hidden for guests. Please log in or register to see it.
  • Attachment This image is hidden for guests. Please log in or register to see it.
  • Attachment This image is hidden for guests. Please log in or register to see it.
  • Attachment This image is hidden for guests. Please log in or register to see it.

Re: 1976 Camaro Street Machine Project ***SOLD*** 1 year, 7 months ago #1951

Car has been sold...thanx
  • Page:
  • 1
Time to create page: 0.18 seconds